Epoxy Floor Coatings
A solid epoxy coat suits a garage or workshop slab that's dusty, stained or cracked, once we grind it clean so the coating bonds to bare concrete instead of grime.
Flooring Contractor in Venus, TX - garage, patio and shop floors built on solid prep
Slabworks Epoxy Floors of Waxahachie coats, polishes and repairs concrete floors in Venus, TX, from garages and patios to pool decks and shop floors, and I come out myself to look at your slab first.
Slabworks Epoxy Floors of Waxahachie does the full range of concrete floor work in Venus, TX, from epoxy and polyaspartic garage coatings to polished, stained and resurfaced concrete. As a flooring contractor based in Waxahachie, we drive over for garages, patios, pool decks, basements and shop floors, and I look at every slab before we talk finishes.
Concrete floor work we do around Venus
A lot of what we see around Venus starts in the garage. There's usually a dark spot where a truck drips, a few hairline cracks, and maybe an old coat of paint flaking off near the door. None of that means the slab is bad. It means the surface needs work before anything goes on top, the same way you'd wire-brush a rusty gate before you paint it.
Outside, patios and pool decks take a beating from the sun and start to scale or fade, and shops and outbuildings need floors that can handle equipment and spills. Some folks want the plain concrete inside their house ground and polished instead of covered up. It's the same mix of work we do up the road in Midlothian, and the prep comes first on every one of them.
- Based in
- Waxahachie, TX 75165
- Hours
- Mon–Sun: 6 AM–11 PM
Floor services we offer Venus homes and shops
Commercial & Industrial Epoxy Floor Coatings
For shops, kitchens and work floors that take carts, forklifts or daily mopping, we build thicker epoxy systems that stand up to the traffic and clean up easily.
Garage Floor Coatings
When the garage floor has tire marks, oil spots and cracks, we repair, grind and coat it with a flake finish that hides dirt and cleans with a hose.
Polyaspartic Floor Coatings
Polyaspartic cures faster than epoxy and holds its color in sunlight, so it suits garages where the door stays open a lot or owners who need the space back sooner.
Metallic Epoxy Flooring
Metallic epoxy gives a living area, game room or showroom a swirled, glossy look, and it needs a flat, well-prepped slab because every low spot shows through.
Urethane Cement Flooring
For commercial kitchens and wash-down areas with hot water, grease and big temperature swings, urethane cement holds up where a standard epoxy can soften or let go.
Polished Concrete Flooring
If you'd rather show off the concrete itself, we grind and polish the slab to a hard, shiny surface that suits shops, open living spaces and heavy foot traffic.
Stained Concrete Flooring
Stain puts color into the concrete rather than on top of it, giving patios and interior slabs a mottled, earthy look with no film on the surface to peel.
Terrazzo Flooring
Terrazzo sets chips of glass or stone into a binder and then gets ground smooth, so it fits entries, lobbies and rooms where you want a long-wearing decorative floor.
Basement Flooring
Below-grade slabs can carry moisture up from the ground, so we check for it before choosing a coating for a basement or any room where dampness has shown up.
Concrete Grinding & Surface Preparation
Before any coating goes down, we grind the slab to open up its surface and fix cracks and chipped spots, which is the step most failed floors skipped.
Concrete Sealing
A clear sealer helps a driveway, patio or bare garage floor shed water and stains when you like the plain concrete look and just want it protected.
Concrete Resurfacing & Overlays
If a patio or slab is pitted, scaled or patched but still sound underneath, an overlay gives it a fresh surface without tearing out the concrete.
Self-Leveling Concrete & Overlays
A self-leveling overlay fills dips and uneven spots in an interior slab so the next floor, from a coating to tile or vinyl, goes down flat.
Pool Deck Coatings & Resurfacing
Pool decks take sun, chlorine and wet feet all season, so we coat or resurface them with textured finishes that give bare feet some grip.
Concrete Floor Stripping & Removal
When old epoxy, paint, glue or tile is failing, we take it off down to sound concrete so the next floor starts clean instead of on top of old problems.
Get a look at your Venus floor before you pick a finish
We reply to every call and message within one business day. After that, I come out to your place in Venus myself, look over the slab and go over the job with you. The estimate is free, done in person and comes with no obligation.
(972) 903-8033What working in Venus means for your permit and price
Building permits in Venus come from the City of Venus Permits Department, and the city requires one to build, alter or enlarge any structure on a home or business lot. If your job needs one, the work waits until it's issued, so that's the part of the schedule nobody can rush. Before anyone starts on your floor, ask them for proof of license and insurance, us included.
We check with the permit office while we plan your job, so you know where things stand before we set a start day. We drive over from Waxahachie for Venus jobs the same way we head up to Hutchins or over to Ennis, and the prep and the steps don't change from one city to the next.
What moves the price is mostly the condition of your slab and the finish you pick, more than the size of the room. The schedule turns on how much prep the floor needs, how long the coating has to cure before you can use it, and the permit answer if there is one. You'll get your own figure when I come out and look at the floor.
How we handle your floor from estimate to finish
I've worked concrete since I was a kid patching barn floors on our family farm, and I started this business in Waxahachie in 2013. Most floor failures I've seen started under the coating, not in it. So we spend the extra time grinding, filling and checking the slab, and I explain each step before we do it, so you know why your floor gets what it gets.
I come out myself to look at your floor and go over the job with you, and I'm on the job with our crew when the work gets done. That way the person who looked at your slab is standing there when it's ground and coated. We're licensed and fully insured. Your satisfaction, guaranteed.
If you're not sure yet what your slab needs, that's fine, and I won't push you toward a finish. Call (972) 903-8033 or send the contact form, and I'll tell you straight what your floor can and can't do, and why.
What Venus heat and county lines mean for your floor
Venus weather and its spot on a county line both change how we plan floor work here. This is what they mean for a garage, a shop or a pool deck.
Summer heat shortens working time
Summer afternoons in Venus run hot, with average highs around 95°F in July and August. Epoxy and polyaspartic set faster in heat, so the window to spread and roll a batch gets short, and a garage slab that's been baking all day can shorten it more. When it's hot, we usually start coating early in the day, keep material out of the sun and mix smaller batches.
Cooler months slow the cure
Winters are milder, with January highs averaging around 57°F, but a slab in an unheated garage or shop can sit colder than the air on a winter morning. Cold concrete slows a coating's cure, so we check the slab's temperature before we start and plan the days so the floor gets the time it needs before you park on it.
Two counties meet here
Venus sits in both Johnson and Ellis Counties, which matters if your property is outside the city limits. Out in unincorporated Ellis County, permits for structures and other work go through the county's Department of Development, not the city. That's worth knowing if you're adding a shop or outbuilding with a new slab, and we sort out which office applies while we plan.
Patios and pool decks in full sun
Outdoor slabs here sit in hard afternoon sun for months at a time, and a dark, smooth coating can get hot underfoot and slick when it's wet. For patios and pool decks we usually steer people toward lighter colors and a textured finish, because bare feet and wet sandals matter more out there than a high shine does.
Questions Venus homeowners ask about concrete floors
How much does an epoxy garage floor cost in Venus, TX?
The cost depends more on the shape your slab is in and the finish you choose than on square footage alone. Cracks to fill, old paint or sealer to grind off and oil soaked into the concrete all add prep, and metallic or polished finishes take more steps than a basic flake coat. I'll give you a figure once I've seen your floor.
Do I need a permit to have my garage floor coated in Venus, TX?
The city's permit list doesn't name floor coatings by themselves, so the surest answer comes from the city in writing. Send the Permit Determination Form to permits@cityofvenus.org, and the Chief Building Official reviews it and sends back a written determination. If your job does need a permit, we handle it.
Who gets the permit in Venus, the homeowner or the contractor?
The city holds the property owner, the contractor or both responsible for getting the proper permits. Starting work before a required permit can bring an added fee of twice the permit fees, at the Building Official's discretion. That's one more reason we settle the permit question before our crew shows up.
How long before I can park on a new garage floor coating?
It depends on the coating and the weather, so I'll give you the schedule for your floor at the estimate rather than guess here. Epoxy and polyaspartic cure at different rates, and both heat and cold change that. We'll tell you when the floor is ready for foot traffic and when it's ready for a tire.
How do I get my garage ready for an epoxy floor?
Clear everything off the floor, including cars, shelves, bikes and anything stored along the walls, because we grind and coat wall to wall. Tell me about any old paint, sealer or spills you know of, since that changes how we prep. We take care of cleaning and grinding the slab itself.
Why do garage floor coatings peel, and how do you prevent it?
Most peeling starts under the coating, when it's rolled over a slab that wasn't ground, cleaned or checked for oil and moisture. Paint-on kits often skip that, so the coating ends up stuck to dust and old sealer instead of concrete. We grind the surface open and fix cracks first, because a coating is only as good as what it's bonded to.
Talk to us about your Venus floor
We pick up seven days a week, from 6 AM to 11 PM, so call (972) 903-8033 or use the contact form whenever you get a minute to look at your slab.